From 3956b70f583490df9ed0d3d16cc89eb5c1af1001 Mon Sep 17 00:00:00 2001 From: Stefano Stabellini Date: Mon, 14 Sep 2020 17:41:08 -0700 Subject: Removed unused container-based usage Initially ImageBuilder was meant to be mainly invoked from a container but in practice ImageBuilder's scripts have been called directly. Remove the old documentation and Dockerfile. Signed-off-by: Stefano Stabellini Reviewed-by: Brian Woods --- README.md | 80 +++------------------------------------------------------------ 1 file changed, 3 insertions(+), 77 deletions(-) (limited to 'README.md') diff --git a/README.md b/README.md index dacd131..f688f28 100644 --- a/README.md +++ b/README.md @@ -11,15 +11,14 @@ the binaries automatically and boot the full system fast. Given a collection of binaries such as Xen, Dom0 and a number of Dom0-less DomUs, ImageBuilder takes care of calculating all loading addresses, editing device tree with the necessary information, and even -pre-configuring a disk image with kernels and rootfses. ImageBuilder -scripts can be used stand-alone, or from an ImageBuilder Container. +pre-configuring a disk image with kernels and rootfses. ImageBuilder has been tested on Xilinx ZynqMP MPSoC boards. An up-to-date wikipage is also available at [wiki.xenproject.org](https://wiki.xenproject.org/index.php?title=ImageBuilder). -## Stand-alone Usage: scripts/uboot-script-gen +## scripts/uboot-script-gen The ImageBuilder script that generates a u-boot script to load all your binaries for a Xen Dom0-less setup is `scripts/uboot-script-gen`. @@ -89,7 +88,7 @@ Where:\ -o specifies the output filename for the uboot script and its source.\ -## Stand-alone Usage: scripts/disk\_image +## scripts/disk\_image The ImageBuilder script that generates a disk image file to load on a SD or SATA drive. This creates 2 partitions: boot partition where the @@ -112,76 +111,3 @@ Where:\ -w specifies the temporary working directory that the script uses for building the disk image, and if not set, one is created in /tmp\ -o specifies the output disk image file name\ - - -## Container Usage - -ImageBuilder comes with a Dockerfile to build a container with all the -required scripts. The following chapters explain how to build it and use -it. - - -### `Dockerfile.image` - -Build the container. - -``` -$ cd imagebuilder - -$ docker build --force-rm --file Dockerfile.image -t imagebuilder . -``` - -### `/imagebuilder_sd` or `/imagebuilder_tftp` - -#### TFTP - -Run the following command to generate a uboot script to tftp all the -necessary binaries automatically: - -``` -$ docker run --rm --privileged=true -ti -v /tmp:/tmp -v /dev:/dev imagebuilder /imagebuilder_tftp -``` - -The generated files are in `/tmp/output`. At the u-boot prompt run: - -``` -tftpb 0xc00000 boot.scr; source 0xc00000 -``` - -If you are using QEMU, you also need to manually setup the ip address. -Run this command instead: - -``` -setenv serverip 192.168.76.2; tftpb 0xc00000 boot.scr; source 0xc00000 -``` - -#### SATA - -Run the following command to generate an image to be written on disk: - -``` -$ docker run --rm --privileged=true -ti -v /tmp:/tmp -v /dev:/dev imagebuilder /imagebuilder_sd -``` - -The generated image is `/tmp/img/zynqmp.img`. Proceed to dd it to a -disk, or pass the file as an argument to QEMU (describing how to use -QEMU to emulate a SATA disk is out of scope for this document). - -At the u-boot prompt you can boot automatically with the following -command: - -``` -scsi scan; load scsi 0:1 0xc00000 boot.scr; source 0xc00000 -``` - -### Add additional DomUs - -Assuming that you have the kernel and ramdisk of another DomU already in -`PACKAGE.md` format, you can configure Imagebuilder to start it -automatically at boot by making the following changes: - -- edit `Dockerfile.image`, add the domU package to the FROM lines -- edit `Dockerfile.image`, add the domU package to the COPY lines -- edit `config`, adding another DomU (NUM_DOMUS, DOMU_KERNEL and DOMU_RAMDISK) - -Rebuild Imagebuilder and rerun imagebuilder_sd/tftp. -- cgit v1.2.3